Hardware references

I²S settings and optical audio links

Existing equipment provides useful engineering context for O2AT. The references below distinguish the electrical pinout, the audio format and the protocol carried over fibre.

I²S is a bus, not an HDMI audio standard

The NXP I²S bus specification, UM11732 defines the serial audio bus. External LVDS implementations add differential drivers and a connector assignment. An HDMI-shaped socket does not establish matching polarity, channel assignment, master-clock requirements or DSD signalling. It must not be connected to a television HDMI port.

LAiV Harmony DAC modes

The original Harmony DAC manual V1.2, section 3.6, gives eight polarity settings. The signs below identify each named differential signal on the numbered connector pin.

Harmony DAC V1.2: selected signal pins
Pin · signalLAiV AudioMode 1Mode 2Mode 3Mode 4Mode 5Mode 6Mode 7
1 · SDOUT−+−+−+−+
3 · SDOUT+−+−+−+−
4 · BCK++−−++−−
6 · BCK−−++−−++
7 · LRCK−−−−++++
9 · LRCK++++−−−−

Swipe horizontally on small screens.

This is a polarity extract, not a complete wiring drawing. LAiV also documents LOCAL and I²S clock selection in section 4.2. Check DSD channel order and all other pins against both endpoints. Read LAiV’s original manual, pages 17 and 20. Later Harmony models have their own manuals.

Matrix Audio IIS·LVDS

Matrix’s four-type pin-definition guide: data and DSD channel differences
TypePin 1 / 3: PCM dataPin 1 / 3: DSD channelPin 7 / 9: DSD channel
A− / +Right − / +Left + / −
B+ / −Right + / −Left + / −
C+ / −Left + / −Right + / −
D− / +Left − / +Right + / −

Across these profiles, BCK uses pins 4 (+) and 6 (−); MCLK uses 10 (+) and 12 (−). The X-SPDIF3 uses switches 1–2 for the profile, switch 3 for MCLK mode and switch 4 for DoP/native DSD handling. Its ON MCLK setting selects 128fs. Use the model’s diagrams for the switch positions; older X-SPDIF 2 settings differ. Pin definitions · X-SPDIF3 manual.

PS Audio and other HDMI-shaped interfaces

PS Audio’s Stellar DAC specifies two HDMI-connector I²S inputs, PCM through 384 kHz and native DSD through DSD256. These product limits do not define a universal LVDS pinout. Confirm the particular transport and DAC model before choosing a Matrix or LAiV profile. PS Audio Stellar DAC specifications.

iFi publishes a further useful example: its data pair uses pins 1 (−) and 3 (+), while its word-clock pair uses 7 (−) and 9 (+). Its guide also assigns DSD enable and power-control pins. Matching the three audio pairs alone is insufficient. iFi’s complete pinout.

Existing uses of SFP and optical transport

MSB ProISL and Cascade

MSB uses SFP as the physical platform for its proprietary ProISL and Cascade links. Its guide explicitly distinguishes these links from Ethernet and from each other. The stock arrangement uses matched single-mode modules and duplex LC fibre. MSB warns that Ethernet optical transmitters can damage its lower-power optical receivers. Only the manufacturer’s approved module and cable combinations should be used.

MSB’s fibre connection guide

HiFi ROSE RS130

The RS130 has distinct optical functions: a network connection and USB 3.0 over fibre. The USB optical port connects to an appropriate fibre hub; the RS130/RD160 connection kit is specifically for USB 3.0 fibre and is not a network kit. These functions must not be conflated merely because the modules have a similar form.

RS130/RD160 kit and quick-start guide · RS130 manufacturer page

These products demonstrate existing optical interface approaches. Their protocols, optical power and endpoint behaviour remain specific to their manufacturers. None establishes O2AT interoperability or endorsement.

What an O2AT endpoint profile needs to declare

A useful bridge profile must identify the connector pin numbering and viewing direction, differential polarities, PCM word framing, DSD channel order and indication, clock ownership and MCLK ratio, supported rates, control-pin voltages and unused pins. Compatibility needs a documented profile and a test at each supported format. A profile name alone is not a wiring instruction.

Return to the O2AT specification